Shown goods: from 1 to 16 (16 total)
In stock
Promotions
Discounted
| Code | photo_camera | Remains | shopping_cart | ||||||
|---|---|---|---|---|---|---|---|---|---|
| 029956 | ![]() | 5050 waterproof Solderless clip 2 pins, strip 10mm Solderless connector for LED strips 5050, in silicone. Strip width 10mm, 2 pins. | 398 pcs |
| |||||
| 029950 | ![]() | 3528 Solderless clip 2 pins, strip 8mm Solderless connector for LED strips 5050, without silicone. Strip width 8mm, 2 pins. | 388 pcs |
| |||||
| 029951 | ![]() | 3528 waterproof Solderless clip 2 pins, strip 8mm Solderless connector for LED strips 3528, in silicone. Strip width 8mm, 2 pins. | 215 pcs |
| |||||
| 029964 | ![]() | 5050 Solderless clip 4 pins, strip 10mm Solderless connector for LED strips 5050, without silicone. Strip width 10mm, 4 pins. | 270 pcs |
| |||||
| 029965 | ![]() | 5050 waterproof RGB Solderless clip 4 pins, strip 10mm Solderless connector for LED strips 5050, in silicone. Strip width 10mm, 4 pins. | 242 pcs |
| |||||
| 029958 | ![]() | 5050 Mounting clip for strips 10mm | 7500 pcs |
| |||||
| 029967 | ![]() | 5050 RGB Mounting clip for strips 12mm | 5415 pcs |
| |||||
| 029952 | ![]() | 3528 Mounting clip for strip 8mm | 840 pcs |
| |||||
| 029941 | ![]() | "+" splitter 2 pins, width 10mm | 334 pcs |
| |||||
| 029938 | ![]() | "+" splitter 2 pins, width 8mm | 317 pcs |
| |||||
| 029944 | ![]() | "+" splitter 4 pins, width 10mm, RGB | 256 pcs |
| |||||
| 029943 | ![]() | Splitter "T" 2 contacts, width 10mm | 174 pcs |
| |||||
| 029939 | ![]() | Splitter "T" 2 contacts, width 8mm | 143 pcs |
| |||||
| 029945 | ![]() | Splitter "T" 4 pins, width 10mm RGB | 146 pcs |
| |||||
| 029947 | ![]() | RGB 4-pin needle connector, double-ended | 5796 pcs |
| |||||
| 030096 | ![]() | 5050 RGB Connector boot Boot for LED connectors 4-pin | 3642 pcs |
|
To speed up and simplify installation, as well as, in the future, the possibility of quick repair work on site, you can use various connectors, splitters, solderless switches and installation clips.
Solderless connecting clips- are quick-release clips for connecting tape-tape or tape-splitter. It can be both for open-type tape and sealed for waterproof tape. The sealed clip has mortise contacts.
Switch for socket 5.5 * 2.1mm, equalizers- a clip with a wire, at the end of which there is a standard 5.5 * 2.1mm socket for connecting a power supply. Also, if there are several lines, you will need jack-to-plug splitters.
Splitters- are a flexible plate with copper tracks. It is necessary for connecting tapes using solderless clips at an angle (L - type), T - shaped and cruciform (+) ways.
Solderless switches with wire- the same solderless clips, but only on one side are connected by wires about 14 cm long. It is used to lengthen connections. There are clip-wire and clip-wire-clip options.
Solderless switches with wire- the same solderless clips, but only on one side are connected by wires about 14 cm long. It is used to lengthen connections. There are clip-wire and clip-wire-clip options.
Transit switches.In the case when the power supply is built-in, access to it is difficult, or the backlight must be switched on/off segmentally (partially), it is possible to use a transit switch with wires. Such a switch is turned on in the gap between the power supply and the power line of the LED strip.
Installation clip - a soft silicone clip for fixing the tape along its course using screws, self-tapping screws or nails.
















