ЧП Ворон. Электронные компоненты и радиомонтажное оборудование. Микросхемы, транзисторы, реле, резисторы, конденсаторы, паяльное оборудование, припой.
Корзина пуста!
ВХОД ДЛЯ КЛИЕНТОВ

Забыли пароль?
Зарегистрироваться

УВАГА! Шановні клієнти магазину в м.Дніпро!

З 18.12.23 магазин в м.Дніпро за адресою вул.Новокримська 58 не працює.
Однак, наш інтернет-магазин відкритий для вас 24/7.
Усі місцеві замовлення можуть бути відправлені кур'єрськими службами.





Поиск:

Enter a search string or click on the microphone icon and begin speaking.

×
История запросов
ваша история поиска пуста
Whole catalog Development toolsModulesBased on STM controllers
Код товара:
023243

Module for STM32 board LCD 2.8 "color TFT, touchscreen, stylus. QDtech

Display module with a resolution of 240x320.
 Module for STM32 board  LCD 2.8
NOT available.
Expected price: 641,70 UAH
from 1 pc : 641,70 UAH
from 5 pcs : 609,50 UAH ( -5,0%)
Prices are indicated at the time of product availability and may change upon receipt

Current balances:

NOT available

Изображение товара

Product description format_size zoom_out zoom_in

touchscreen
stylus
ILI9325/ILI9331 controller

Pin Number Mark Description Function
1 CS LCD chip select signals Active low
2 RS Instruction/data register select RS = 1: Instruction Register
RS = 0: data register
3 WR Write Data WR = 0, RD = 1
4 RD Reading data WR = 1, RD = 0
5 RESET LCD reset Low reset
6 D1 Data Bus Low 8: D1-D8 
high 8: D10-D17 (8 mode when connected using high 8)
7 D2
8 D3
9 D4
10 D5
11 D6
12 D7
13 D8
14 D10
15 D11
16 D12
17 D13
18 D14
19 D15
20 D16
Twenty one D17
Twenty two GND Negative power supply module Then the power ground GND
Twenty three BLCNT Backlight brightness adjustment You can use IO or PWM to control the backlight brightness
Twenty four VCC Positive power supply module QDtech module supports 5V and 3.3V power supply, a 3.3V power supply J1 shorted, 5V power supply must be disconnected J1
25 VCC
26 GND Negative power supply module Then the power ground GND
27 GND
28 BLVCC 3.3V positive external backlight Short disconnect R3 R4, then use the onboard 3.3V power supply, do not take this pin; when the backlight may require a separate power supply connected to this pin through a 3.3V supply, then disconnect shorted R3 R4
29 TP_SO Touch panel SPI data output Connected to the hardware or simulated SPI MISO
30 TP_SI SPI data input touch panel Connected to the hardware or simulated SPI MOSI
31 TP_IRQ Touch panel interrupted Detecting the touch panel is pressed, compared with low
32 NC Vacant do not take Vacant do not take
33 TP_CS The touch panel chip select signals Link to hardware or simulated SPI's CS, active low
34 TP_SCK Touch panel SPI clock signal Connected to the hardware or simulated SPI SCK
 



Leave your feedback or ask a question

Only this product is discussed here. Off topic comments will be deleted! Please follow the Commenting Rules.

The data presented in the product description are for reference only and may differ from those indicated by the manufacturer.
To carry out technical calculations and obtain the exact parameters of the goods, use the datasheets from the manufacturer's website.

If you need additional information, or you found an error in the description, or have other questions about this product, then our manager will help you: Денис - Днепр unknown